Posts tagged: skin

SopiGuard Skin for Macbook Pro with Touch Bar

By , December 16, 2016 11:30 pm

I recently got a new 13″ ¬†Macbook Pro with TouchBar. This is a 2016 model and the TouchBar is a bit gimmicky, but that’s another story. I wanted to keep it svelte and thin, but also wanted some protection. I looked on Amazon for a skin and finally found a version from a company called SopiGuard. At the time, it had one review and it was not a good one. The reviewer didn’t like anything about it. So I bought it.

Nuts you say? Well, I had a feeling they just didn’t understand how to install it. So, when it arrived I began to transfer my files from one Macbook Pro (i5 2.9 GHz) to my new one (i7 3.3 GHz). The kit has 3 parts rolled up in a nice box. Despite the nice packing, there was a wrinkle in one main piece. More on that later.

Here's my computers transferring files and the SopiGuard kit on top.

Here’s my computers transferring files and the SopiGuard kit on top.

So, a while back I had installed a skin on my Macbook. I learned that the trick was to spray a fine mist of water on the laptop so that you could move the skin around and adjust it. If you do not do this, the large unwieldy self adhesive skin is really hard to position and you’ll be peeling it off to reposition it over and over. The problem is that when you peel it off, odds are food you’ll stretch it and then it doesn’t fit anymore.

So with that in mind, I sprayed a fine mist of water onto my laptop. It’s waterproof and the laptop was turned off. There is little risk of problems from the fine mist.

Spray a fine mist to start.

Spray a fine mist to start.

Next used a knife to pick out the cutouts for the apple logo. I most did OK, but the laser cut wasn’t perfect and I had to tug a little. That left a little imperfection that I’ll show you later. It’s really small. Anyhow, because of the water, I was able to position the skin and then move it around a bit. I started by lining up the Apple logo perfectly. When I got it where I wanted it, I used a credit card as a squeegee and got the water out, keeping a paper towel handy to catch the drips.

You can hardly tell there's a skin on it!

You can hardly tell there’s a skin on it!

The color of the skin was a bit darker than the space gray, but it wasn’t so bad after I got used to it. The skin is also slightly metallic so it enhances the laptop quite well. Now all was not perfect. There was a wrinkle in the skin before I even placed it on the laptop. I am hoping that this small wrinkle will settle over time.

Can you spot the small wrinkles?

Can you spot the small wrinkles?

Also as I mentioned, the area around the Apple logo wasn’t perfect because the cutout left a little piece that I had to tug at. However, I’m being nit picky as you can see here, it’s pretty darn close. Also I guess there’s a tiny shift right. Very tiny.

Small imperfection in upper right of logo.

Small imperfection in upper right of logo.

Well, the last thing was the bottom. It actually ended up being the hardest as it has the most cutouts. I got it applied, but there are many parts that are only ok. I had to pull it up a few times and sure enough, it stretched.

Bottom was the hardest, but it's still pretty good.

Bottom was the hardest, but it’s still pretty good.

There’s holes for the tiny screws and the speaker exit cutouts as well as the notch along the top for the screen. In the end, I stretched it a bit and the upper left cutout for the rubber feet isn’t perfect. If you look really close, you can tell the skin doesn’t sit perfectly.

However, all in all the skin looks great and it does protect the majority of the laptop from scrapes and scratches. For the $16 I paid for it, it’s a pretty good deal. The bad reviews you see are the fact that it’s tricky to install a large self adhesive skin. Use some of the tricks I’ve shared here and you should get good results. I’d recommend this kit!

Here’s a link to the kit on Amazon. SopiGuard Skin.

Good luck to you!

The Merry Go round begins anew

By , September 26, 2010 8:48 pm

So I finally broke down and got an iPhone4. It’s a really nice unit, but I lost all my nice un-Apple approved applications. Somehow, I’ve found that I really didn’t need all those extra items. I’ve been able to find replacements for most items except for the hotspot application.
However, a new problem arises. It’s time for a case. Yeah, after all the time and money that I have spent on cases for my 3GS, I find myself starting over again. So what to get? There were a few criteria. One – I didn’t want a huge aberration of a case that spoiled the nice design. Two – I really wanted a white iPhone, but its been reported that they are not going to be out for a while. What’s a guy to do.

For the first item, I decided to take advantage of the free case program from Apple. Most of the free cases my friends got were the huge aberrations that I mentioned above. They just about doubled the thickness of the phone. The cleanest thing I could find was the bumper case from Apple. A very nicely made and ridiculously overpriced piece of plastic. However, this was going to be free, so I went for it. The downside? The bumper case doesn’t protect the front or back glass. I’d need something else for that.

Then I came across a curious thing. You may recall that I got a nice “Leather” look skin for my laptop. Well, the same folks made skins for the iPhone4. They even had one in white! Yea, you know where this is going.

The SGP iPhone4 skin kit

Easy to put on. Leaves no residue.

Look, I have a white iPhone4 - sorta.

So there you have it. I have a white iPhone4 now. It only cost me $17.99 + shipping.

I am sure as time goes by, my case obsession will run rampant again. For now, this combination is good and it has already saved me 2 times as I dropped my phone. Let’s see how long it takes before I see something cooler.

Panorama Theme by Themocracy